472

A place for discussion of off topic subjects. Pretty much anything goes - just keep it civil, please!

Moderators: Casey 65, Kid

Post Reply
neil66
Posts: 35
Joined: January 13, 2007, 9:43 am
Location: valley view texas

472

Post by neil66 »

472 rotating assembly for 900 dollars good or bad . tunnel ram for 460 will it fit under hood of 66 slick .
neil66
User avatar
Greg D
Posts: 10113
Joined: September 13, 2006, 4:39 pm
Location: Podunk Iowa
United States of America

Post by Greg D »

The tunnel doesn't need to fit under the hood. A pair of velocity stacks hanging out of the hood looks cool!
1964 F 100 - I am going to do "something" with it.......

viewtopic.php?f=32&t=15942

1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD


~ Yes - I adopted another cat..............

Cam L Milan,
You'll be missed my friend.
User avatar
bigtrip460
Posts: 305
Joined: February 4, 2007, 7:34 pm
Location: OHIO!
Contact:

Post by bigtrip460 »

you get what you pay for. you should probably (hopefully) be ok as long as you dont spin it to the moon. what are the parts? maybe after the machine work and balancing it might not be a good deal at all, though. I am guessing chinese but its not always a bad thing. I have been told the more you spend up front the less you spend on the back end.
Garbz

Post by Garbz »

I have a 472 in christine....

FYI 472 is a 460 with a .060 over bore. You gain 6 cubic inches. at .030 and 12 at .060

900 bucks is awfull expensive for 12 cubic inches, seeing as it uses a stock crank, rods and over bore slugs.

My D3VE block needed the 60 over to get number six in spec so i had the machinist take all them out to 60.

Garbz

PS Tunnel rams work horrible on the street.. Need some big bump action and compression plus about five grand of rev to even begin to use it. Figgure about eight grand of bottom end and head work to get going.
User avatar
FORDBOYpete
Posts: 850
Joined: July 21, 2006, 8:30 am
Location: East Central Florida USA

Post by FORDBOYpete »

Neil66,

Yeah, I agree 100% with Garbz!
Tunnel ram isn't best choice for street engine, unless you plan to make it into a basis for Tuned Port EFI Set up.
But for carburetion, it's wrong if you want to run best on the street.

Also what exactly does "rotating assembly" consist of? Crank & Rods are same as a box stock 460, unless. . . . :hm:
You're starting with a 429CID Engine.


So $900 for basically 8, .060" over, pistons seems just a tad pricey to me. Also, I never buy used pistons,
if that's what they are,without 1st checking for damage like fractures or stress problems.

Hey it's just my :2cents: on the subject here. I run 460s & have for years.

When set up "Right" they're both NASTY on demand and/ or economical, if I take care driving them. :steering:

Plus, not many street vehicles get by them. secret.gif

FBp Bolt.gif
Change is the Only Constant
BigTim
Posts: 890
Joined: August 6, 2006, 4:26 pm
Location: Slickless

Post by BigTim »

FORDBOYpete wrote:
When set up "Right" they're both NASTY on demand and/ or economical, if I take care driving them.
Hint hint.
Post Reply