472
The tunnel doesn't need to fit under the hood. A pair of velocity stacks hanging out of the hood looks cool!
1964 F 100 - I am going to do "something" with it.......
viewtopic.php?f=32&t=15942
1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD
~ Yes - I adopted another cat..............
Cam L Milan,
You'll be missed my friend.
viewtopic.php?f=32&t=15942
1987 Mustang LX Convertible, 2.3 Auto - cruiser.
1994 F 150 XLT 2WD
~ Yes - I adopted another cat..............
Cam L Milan,
You'll be missed my friend.
- bigtrip460
- Posts: 305
- Joined: February 4, 2007, 7:34 pm
- Location: OHIO!
- Contact:
you get what you pay for. you should probably (hopefully) be ok as long as you dont spin it to the moon. what are the parts? maybe after the machine work and balancing it might not be a good deal at all, though. I am guessing chinese but its not always a bad thing. I have been told the more you spend up front the less you spend on the back end.
-
Garbz
I have a 472 in christine....
FYI 472 is a 460 with a .060 over bore. You gain 6 cubic inches. at .030 and 12 at .060
900 bucks is awfull expensive for 12 cubic inches, seeing as it uses a stock crank, rods and over bore slugs.
My D3VE block needed the 60 over to get number six in spec so i had the machinist take all them out to 60.
Garbz
PS Tunnel rams work horrible on the street.. Need some big bump action and compression plus about five grand of rev to even begin to use it. Figgure about eight grand of bottom end and head work to get going.
FYI 472 is a 460 with a .060 over bore. You gain 6 cubic inches. at .030 and 12 at .060
900 bucks is awfull expensive for 12 cubic inches, seeing as it uses a stock crank, rods and over bore slugs.
My D3VE block needed the 60 over to get number six in spec so i had the machinist take all them out to 60.
Garbz
PS Tunnel rams work horrible on the street.. Need some big bump action and compression plus about five grand of rev to even begin to use it. Figgure about eight grand of bottom end and head work to get going.
- FORDBOYpete
- Posts: 850
- Joined: July 21, 2006, 8:30 am
- Location: East Central Florida USA
Neil66,
Yeah, I agree 100% with Garbz!
Tunnel ram isn't best choice for street engine, unless you plan to make it into a basis for Tuned Port EFI Set up.
But for carburetion, it's wrong if you want to run best on the street.
Also what exactly does "rotating assembly" consist of? Crank & Rods are same as a box stock 460, unless. . . .
You're starting with a 429CID Engine.
So $900 for basically 8, .060" over, pistons seems just a tad pricey to me. Also, I never buy used pistons,
if that's what they are,without 1st checking for damage like fractures or stress problems.
Hey it's just my
on the subject here. I run 460s & have for years.
When set up "Right" they're both NASTY on demand and/ or economical, if I take care driving them.
Plus, not many street vehicles get by them.
FBp
Yeah, I agree 100% with Garbz!
Tunnel ram isn't best choice for street engine, unless you plan to make it into a basis for Tuned Port EFI Set up.
But for carburetion, it's wrong if you want to run best on the street.
Also what exactly does "rotating assembly" consist of? Crank & Rods are same as a box stock 460, unless. . . .
You're starting with a 429CID Engine.
So $900 for basically 8, .060" over, pistons seems just a tad pricey to me. Also, I never buy used pistons,
if that's what they are,without 1st checking for damage like fractures or stress problems.
Hey it's just my
When set up "Right" they're both NASTY on demand and/ or economical, if I take care driving them.
Plus, not many street vehicles get by them.
FBp
Change is the Only Constant

